Steam Equipment

Steam Traps is a tool that functions to get rid of water from steam, where this water is useless because it actually provides obstacles or other losses to the flow of steam. The steam trap is also installed where condensed water vapor accumulates and then it is automatically mechanically discharged into the water tank in general. The steam trap installation should not be reversed either, pay attention to the direction of the arrow on the steam trap body. The use of steam traps is usually in the drain line of a system, where the system only removes the steam in it from time to time.

Adca float and thermostatic steam trap FLT 25

Description

The FLT25 is a series of float and thermostatic steam traps with an inbuilt air vent for controlling condensate discharge and ensuring maximum heat transfer in the system. Unit heaters, heat exchangers, dryers, jacketed vessels, and other applications that require continuous discharge are examples of typical applications.

Type

Adca float and thermostatic steam trap FLT 25

Fitur

-

Adca float and thermostatic steam trap FLT 21

Description

The FLT21 is a series of float and thermostatic steam traps with an integral air vent that are designed to modulate condensate discharge and maximize system heat transfer. Unit heaters, heat exchangers, dryers, jacketed vessels, and other applications requiring continuous discharge are examples of common applications.

Type

Adca float and thermostatic steam trap FLT 21

Fitur

-

Adca FLOAT AND THERMOSTATIC STEAM TRAPS FLT 20

Description

The FLT20 is a series of float and thermostatic steam traps with integral air vent designed for modulating discharge of condensate, ensuring maximum system heat transfer. Typical applications include unit heaters, heat exchangers, dryers, jacketed vessels and other applications where continuous discharge is essential.

Type

FLT20-4,5
FLT20-10
FLT20-14 

Fitur

Modulating discharge of condensate at steam temperature.
Unaffected by sudden or wide load and pressure variations.
No backing-up with condensate.
Excellent air discharge through its integrated air vent. 
Flow direction can be easily changed by repositioning the body in 
relation to the mechanism and cover.

Adca Steam Trap DT40 2

Description

The thermodynamic DT40/2 disc steam traps are compact and lightweight-easy to install traps, excellent for high pressure systems, including steam tracing applications. The insulation cover ensures a consistent operation and makes it particularly suitable for those applications where the weather conditions, such as rain and wind, may affect the normal operation. These traps have only one moving part and offer a wide operating range, without adjustment.

Type

Adca steam trap DT40/2 

Fitur

Intermittent discharge.
Integral air vent.
Standard insulation cover.
Operates on superheated steam.
The seat and disc can be easily replaced in field without removing the 
trap from the line.
Unaffected by water hammer and vibrations.
Built-in easy-to-clean strainer

Gestra NRGS 11_2 NRGS 16_2

Description

The NRGS 1...-2 has its level switch integrated in the electrode case for the control of all functions. An external switching device is not required. The NRGS 1...-2 has two electrode tips for the detection of low-water level. The low-level alarm is signalled via two separate switching channels. The NRGS 1...-2 is designed to detect and signal different levels in conductive liquids. It is appropriate for use in the power supply, water and chemical industries and particularly suitable for applications in steam boilers and feedwater tanks.

Type

Gestra NRGS 11_2 
Gestra NRGS 16_2

Fitur

The conductivity of the liquid is used to signal the liquid 
level. Some liquids are conductive, which means that they 
allow an electric current to flow through them. For the safe 
functioning of this device a minimum conductivity of the 
liquid to be measured is required.
The conductivity measurement method can detect two 
conditions: electrode rod submerged or exposed, meaning 
switchpoint reached or not reached. Before installation, 
the length of the electrode tip must be cut to the required 
switching levels, e. g. for max./min. alarm, controlling of 
a valve or pump.

Gestra NRGS 11_1 NRGS 16_1 NRGS 16_1S

Description

The compact systems NRGS 11-1 and NRGS 16-1 work according to the conductivity measurement principle. With the NRGS 16-1 a maximum of 4 levels can be signalled in conductive liquids:

Type

Gestra NRGS 11_1 
Gestra NRGS 16_1 
Gestra NRGS 16_1S

Fitur

The conductivity of the liquid is used to detect the liquid 
level. Some liquids are conductive, which means that they 
allow an electric current to flow through them. For the safe 
functioning of this device a mimimum conductivity of the 
liquid to be monitored is required.
The conductivity measurement method can detect two 
conditions: electrode tip submerged or exposed, meaning 
switchpoint reached (or exceeded) or not yet reached. 
Before installation, the length of the electrode rod must be 
adapted to the switching levels, e.g. for max./min. alarm, 
controlling of a valve or pump.

Yoshitake Steam Trap TSD 42 TSD 42F

Description

As a yoshitake distributor in Indonesia, PT Indotama Niaga Teknik offers products from the Yoshitake brand, namely the Yoshitake Steam Trap TSD 42 TSD 42F to meet industrial and manufacturing needs.

Type

Yoshitake Steam Trap TSD 42 TSD 42F

Fitur

TSD-42
*High corrosion resistance due to main parts made of stainless steel.
*Operate under 425 degrees C temp. and 4.2 MPa pressure.
*The adoption of a bimetal solves air locking, and ensures a smooth discharge of cold condensate and air at the start of operation.
*Can be installed vertically or horizontally as desired.
*Built-in strainer
*\\\"Insulation cover\\\" avoiding frequent on-off is available.

TSD - 42F
*High corrosion resistance due to main parts made of stainless steel.
*Operate under 425 degrees C temp. and 4.2 MPa pressure.
*The adoption of a bimetal solves air locking, and ensures a smooth discharge of cold condensate and air at the start of operation.
*Can be installed vertically or horizontally as desired.
*Built-in strainer
*\\\"Insulation cover\\\" avoiding freequent on-off is available.

Yoshitake Steam Trap TSF 10 TSF 10F

Description

As a yoshitake distributor in Indonesia, PT Indotama Niaga Teknik offers products from the Yoshitake brand, namely the Yoshitake Steam Trap TSF 10 TSF 10F to meet industrial and manufacturing needs.

Type

Yoshitake Steam Trap TSF 10 TSF 10F

Fitur

TSF-10
Float Steam Trap
* Can discharge condensate effectively without retention, and realize energy saving steam system without steam loss.
* Incorporated thermostatic air vent discharges air inside piping and shortens warming-up time.
* With turning the cock, it is possible to meet various flow direction such as horizontal or vertical installation.
* Flow direction can be switched easily without disassembly such as detaching the cover.
* Since the main parts are installed on the cover with the body installed on the piping, inspection and parts replacement can be easily.

TSF-10F
Float Steam Trap
* Can discharge condensate effectively without retention, and realize energy saving steam system without steam loss.
* Incorporated thermostatic air vent discharges air inside piping and shortens warming-up time.
* With turning the cock, it is possible to meet various flow direction such as horizontal or vertical installation.
* Flow direction can be switched easily without disassembly such as detaching the cover.
* Since the main parts are installed on the cover with the body installed on the piping, inspection and parts replacement can be easily.

Yoshitake Steam Trap TD 30NA

Description

As distributor yoshitake in indonesia, PT indotama niaga teknik offer product from brand yoshitake , that is Yoshitake Steam Trap TD 30NA to meet the need industrial and manufactur

Type

Yoshitake Steam Trap TD 30NA

Fitur

1. Bimetal eliminates air-binding and guarantees a smooth release of cold condensate or air during startup, allowing steam equipment to start up efficiently.
2. The unique heat treatment of the stainless steel valve disc and valve seat ensures long-term durability.
3. Without detaching the steam trap from the pipe, the valve disc, valve seat, and bimetal can be replaced on site.
4. Simple structure allows for easy maintenance and inspection: the valve disc is the only moving item.
5. It's small, light, and affordable. Adjustment-free and suitable for a wide working pressure range.
6. Easy to plumb and install in any direction.
7. No inappropriate operation or steam leakage due to the type of air insulation.
8. The built-in strainer eliminates the need for a strainer prior to using the device.
9. Large capacity of discharge

Yoshitake Steam Trap TD 10NA

Description

As distributor yoshitake in indonesia, PT indotama niaga teknik offer product from brand yoshitake , that is Yoshitake Steam Trap TD 10NA to meet the need industrial and manufactur

Type

Yoshitake Steam Trap TD 10NA

Fitur

1. Bimetal solves air-binding problem and ensures a smooth discharge
of cold condensate or air at the start of operation, enabling steam
equipment to efficiently start to run.
2. The stainless steel valve disc and valve seat, which are subjected to
special heat treatment, offers excellent durability.
3. The valve disc, valve seat and bimetal can be replaced on site without
disconnecting the steam trap from the piping.
4. Easy maintenance and inspection due to simple structure: the valve
disc is only movable part.
5. Compact, lightweight and inexpensive. Applicable in wide working
pressure range and adjustment-free.
6. Installable in any direction and easy to plumb.
7. Free of improper operation and steam leakage due to air insulation
type.
8. Built-in strainer eliminates requirement for strainer before the product.
9. Large discharge capacity

Yoshitake Steam Trap Tsf 8

Description

PT Indotama Niaga Teknik as distributor steam trap yoshitake in indonesia, offer product from brand yoshitake, that is Yoshitake Steam Trap Tsf 8 21, to meet the need industrial and manufactur

Type

Model : TSF-8

Fitur

1. The TSF-8 can discharge condensate effectively without retention due to reliable operation by difference in specific gravity between steam and condensate.
2. Since the main parts are attached on the cover and it is possible to dismount the cover with the body connected to the piping, inspection and parts replacement can be conducted easily.
3. Excellent corrosion resistance and durability because the main parts are all made of stainless steel.
4. A strainer is incorporated to protect the internal parts from foreign substances and improve durability

Gestra Therodynamic Steam Traps DK Series

Description

As distributor steam trap in indonesia, PT Indotama Niaga Teknik offer product from brand gestra , that is Gestra Therodynamic Steam Traps DK Series (DK 45, DK 47 L, DK 57 L, DK 47 H, DK 57 H), To meet the need industrial and manufacture

Type

Gestra Therodynamic Steam Traps DK Series :
DK 45
DK 47 L
DK 57 L
DK 47 H
DK 57 H

Fitur

• Discharge with virtually no banking-up
• Robust, insensitive regulator
• Installation in any position
• Max. admissible back pressure 80 % of the upstream pressure

Gestra Steam Trap UNA 27

Description

As distributor steam trap in indonesia , PT Indotama Niaga Teknik offer product from brand gestra that is Gestra Steam Trap UNA 27, to meet the need industrial and manufacture

Type

Gestra Steam Trap UNA 27

Fitur

-

Gestra Thermostatic Steam Trap MK 35 31

Description

As distributor gestra steam trap in indonesia. PT Indotama Niaga Teknik offer product from brand gestra, that is Gestra Thermostatic Steam Trap MK 35, to meet the need industrial and manufactur

Type

Gestra Thermostatic Steam Trap MK 35

Fitur

• Control capsule of Hastelloy® and Stainless Steel for
superior corrosion resistance.
• Tandem seated control capsule combined with a venturi
style orifice uses a unique double valve and seat for tight
shutoff, cyclical discharge and superior dirt-handling
ability.
• Forged Steel Body and Cover.
• Standard (N) capsule discharges hot condensate at
approximately 18°F (10°C) below saturation temperature
throughout its operating range. One internal regulator for
all pressure ranges.
• Resistant to water hammer.
• Self-draining – will not freeze when installed in gravity
drainage position.
• Automatically vents air and non-condensable gases and
has a high (>3:1) cold water capacity for rapid start-up.
• Operates with zero steam loss throughout its operating
range, saving steam and money during the life of the trap.
• Can be installed in any position.
• Small profile and lightweight for ease of use and
maintenance.
• Internal stainless steel strainer.
• Three (3) year guarantee.

Gestra Thermostatic Steam Trap MK 36 A7

Description

As distributor gestra steam trap in indonesia. PT Indotama Niaga Teknik offer product from brand gestra, that is Gestra Steam Trap MK 36/A7, to meet the need industrial and manufactur

Type

Gestra Steam Trap MK 36/A7

Fitur

• Tandem seated control capsule combined with a venturistyle orifice uses a unique double valve and seat for tight shutoff, cyclical discharge and superior dirt-handling ability.
• Discharges hot condensate at approximately 18°F (10°C) below saturation temperature throughout its operating range. One internal regulator for all pressure ranges.
• Cyclical discharge eases audible/visual performance checking.
• Resistant to water hammer.
• Self-draining – will not freeze when installed in gravity drainage position.
• Automatically vents air and non-condensable gases and has a high (4:1) cold water capacity for rapid startup.
• Operates with zero steam loss throughout its operating range, saving steam and money during the life of the trap.
• Can be installed in any position.
• Two (2) year guarantee

Gestra Steam trap DK 45

Description

As distributor steam trap in indonesia , PT Indotama Niaga Teknik offer product from brand gestra that is Gestra Steam trap DK 45, to meet the need industrial and manufacture

Type

Gestra Steam trap DK 45

Fitur

The thermodynamic steam trap features a movable valve
disk that rests on a double seat. The condensate enters
the steam trap from below, thereby lifting the disk off its
seat. It is then deflected by 180° and flows through the
small seat orifice into the discharge line. As the temperature
of the condensate increases, upstream pressure builds up
in the space above the valve disk. When the condensate
evaporates into steam, a low-pressure area is formed under the disk due to the increased flow velocity, forcing the
disk downwards against its bearing surface and stopping
all flow. Since the pressure above the valve disk is acting
on a larger surface area, the closing force is much higher than the pressure pushing against the disk from the
inlet side. As the steam loses heat, some of it condenses,
reducing the pressure above the valve disk and hence the
closing force. As soon as the pressure on top of the disk
has dropped to a value that equals the opening pressure produced by the upstream pressure, the disk is lifted
off its seat, and the cycle repeats itself. External factors
such as heat, wind, precipitation etc. can effect the functioning and performance of the thermodynamic steam trap
considerably. However, the DK 45 is not influenced by these

Gestra Steam Trap BK 46 PN 40 DN 15 20 25

Description

As distributor steam trap in indonesia , PT Indotama Niaga Teknik offer product from brand gestra that is Gestra Steam Trap BK 46 PN 40 DN 15 20 25, to meet the need industrial and manufacture

Type

Gestra Steam Trap BK 46 PN 40 DN 15 20 25

Fitur

-

Gestra Thermostatic Steam Trap BK 212 ANSI 2500

Description

As distributor thermostatic steam trap in indonesia , PT Indotama Niaga Teknik offer product from brand gestra that is Gestra Thermostatic Steam Trap BK 212 ANSI 2500, to meet the need industrial and manufacture

Type

Gestra Thermostatic Steam Trap BK 212 ANSI 2500

Fitur

• Forged alloy steel body with Titanium body shield to resist
flashing damage.
• Titanium alloy valve and seat.
• Pressure assisted “fail open-only” design.
• Standard factory setting discharges hot condensate in a
modulating fashion at approximately 18°F (10°C) below
saturation temperatures throughout its operating range.
• One internal bimetallic regulator for all applicable body
pressure ranges.
• Staged “control valve” style nozzle reduces wiredrawing
damage by reducing flashing. Totally unaffected by water
hammer.
• Self draining – will not freeze when installed in gravity
drainage position. Can be installed in any position.
• Automatically vents air and non-condensable gases and has
a very high (>9:1) cold water capacity for rapid start-up.
• Operates with zero steam loss throughout its operating
range saving steam and money during the life of the trap.
• Easy in-line inspection and maintenance – no need to
remove the trap from the piping to clean or replace the
internals.
• Valve and seat are a single, modular replacement part.
• Internal stainless steel strainer.
• Integral check valve design.
• Two (2) year guarantee

Gestra Thermostatic Steam Trap BK 15 ANSI 300

Description

As distributor Thermostatic Steam Trap in indonesia , PT Indotama Niaga Teknik offer product from brand Gestra that is Gestra Thermostatic Steam Trap BK 15 ANSI 300 (DN 40 and 50), to meet the need industrial and manufacture

Type

Gestra Thermostatic Steam Trap BK 15 ANSI 300

Fitur

• Forged carbon steel body.
• Pressure assisted fail open design.
• Modulating bimetallic regulator with fatigue-free stainless
steel plates. No adjustment required.
• In-line adjustment available for characterization to process
conditions and effects of back pressure.
• Discharges hot condensate at approximately 18°F (10°C)
below saturation temperature throughout its operating
range. One internal regulator for all pressure ranges.
• Operation is unaffected by water hammer or superheat.
• Self draining – will not freeze when installed in gravity
drainage position.
• Automatically vents non-condensables and has a high
(>3:1) cold water capacity for rapid start-up.
• Operates with zero steam loss throughout its operating
range saving steam and money during the life of the trap.
• Easy in-line inspection and maintenance – no need to
remove the trap from the piping to replace the internals.
• Can be installed in any position.
• Internal stainless steel strainer.
• Integral check valve design.
• Two (2) year guarantee

Pennant Thermodynamic Steam Traps PT 13

Description

As distributor pennant steam traps in indonesia. PT Indotama Niaga Teknik Offer Product from brand pennant namely Pennant thermodynamic steamtrap PT 13. To meet the need industrial and manufacture

Type

Pennant Thermodynamic Steam Traps PT 13

Fitur

  Complete stainless steel internals ensure   better mechanical & corrosion resistance properties.l  Condensate  entry  below  the  dis  c,  concentric  to  the disc/seat ensures a clean & parallel lift of the dis  c with ref   erence to the seat, eliminating localis ed wear & tear.l  The dis  c & seat are fully hardened by a special hardening process, to withstand continuous, prolonged operation.l  Perfect shut off, no steam loss.l  Robust, maintenance free, fully guaranteed

Pennant Thermodynamic Steam Traps PT 11

Description

Indotama Niaga Teknik as pennant distributor in indonesia offer various type of pennant steam traps like Pennant Thermodynamic Steam Traps PT 11 to meet the need industrial and manufacture steam equipment steam trap

Type

Pennant Thermodynamic Steam Traps PT 11

Fitur

Complete   stainless   steel   construction   ensures   better   mechanical  and  corrosion  resistance  properties.  The  disc  and  seat  are  hardened  by  a  special  induction  hardening  process with seat harder than disc, to withstand continuous, prolonged operation.
Condensate entry below the disc, concentric to the disc/seat ensures a clean and parallel lift of the disc with reference to the seat, eliminating localized wear and tear.
The inbuilt strainer screen is of adequately large area.Ideal for fluctuating loads and pressures.Perfect shut-off, no steam loss

Pennant Thermodynamic Steam Traps PT 10

Description

Indotama Niaga Teknik as distributor pennant steam trap in indonesia. offer steam traps product namely Pennant Thermodynamic Steam Traps PT 10. to meet the need industrial and manufactur steam trap and steam equipment sparepart

Type

Pennant Thermodynamic Steam Traps PT 10

Fitur

Complete   stainless   steel   construction   ensures   better   mechanical  and  corrosion  resistance  properties.  
The  disc  and  seat  are  hardened  by  a  special  induction  hardening  process with seat harder than disc, to withstand continuous, prolonged operation.
Condensate entry below the disc, concentric to the disc/seat ensures a clean and parallel lift of the disc with reference to the seat, eliminating localized wear and tear.
The inbuilt strainer screen is of adequately large area.Ideal for fluctuating loads and pressures. Perfect shut-off, no steam loss

Gestra Ball Float Steam Trap UNA 38 PN 100 DN 15 to DN 50

Description

As distributor gestra in indonesia. PT Indotama Niaga Teknik offer product from brand gestra namely Gestra Ball Float Steam Trap UNA 38 PN 100 CL 600 DN 15 to DN 50 to meet the need industrial and manufacture steam trap steam equipment

Type

Gestra Ball Float Steam Trap UNA 38 PN 100 and Class 600 DN 15 to DN 50

Fitur

-

Gestra Simple Cooler PK 40

Description

Indotama Niaga Teknik as distributor steam equipment gestra in indonesia , We are Offer product from brand gestra ,namely Gestra Simple Cooler PK 40 to meet the need of industrial and manufacture in indonesia

Type

Gestra Simple Cooler PK 40

Fitur

-

Gestra vaposcope vk 14 vk 16

Description

Gestra vaposcope vk 14 vk 16 : is a sight flow indicator specially designed for monitoring flow conditions in pipelines. The equipment is installed upstream of a steam trap and enables the user to evaluate the performance of the steam trap. The Vaposcope® is used for checking steam traps for banking up of condensate or steam loss.

Type

Gestra vaposcope vk 14 vk 16

Fitur

-

Gestra Ball Float Steam Traps UNA 45 46

Description

Gestra Ball Float Steam Traps UNA 45 46 - GESTRA UNA 4 ball float steam traps cannot fail to impress, with their simple, modular design that makes them perfectly flexible in use.

Type

 Gestra Ball Float Steam Traps UNA 45 46 

Fitur

-

Adca Float and Thermostatic Steam Traps

Description

Jual adca float and thermostatic steam traps | Distributor adca float and thermostatic steam trapsIndotama niaga teknik is Distributor ADCA float and steam traps are manufactured to high quality and are designed for all types of low and high pressure steam. We have stocks product of Adca Float and Thermostatic Steam Traps with the following type.

Type

Adca Float and Thermostatic Steam Traps FLT17LC - DOWNLOAD
Adca Float and Thermostatic Steam Traps FLT17 | DN 15 -25 - DOWNLOAD
Adca Float and Thermostatic Steam Traps FLT17 | DN 40 - 50 - DOWNLOAD

Fitur

    Modulating discharge.
    Discharges condensate at steam temperature.
    Unaffected by sudden or wide load and pressure changes.
    Excellent air discharge (by thermostatic air vent).

Gestra Thermostatic Steam Traps MK

Description

Jual Gestra Thermostatic Steam Traps MK | Distributor Gestra Thermostatic Steam Traps MK . Thermostatic steam traps for removing condensate from steam or for venting steam pipes. The distinguishing feature of the MK series is the excellent responsiveness of the membrane regulator. We have stock products of thermostatic steam traps MK Series GESTRA with the following types.

Type

    Gestra Thermostatic Steam Trap MK 25
    Gestra Thermostatic Steam Trap MK 35
    Gestra Thermostatic Steam Trap MK 36
    Gestra Thermostatic Steam Trap MK 45

Fitur

    Very sensitive response characteristic
    Function is not impaired by high back pressure
    Automatic air-venting (trap can be used for thermal air-venting in steam systems)
    Installation in any position (horizontal and vertical lines)
    High hot-water capacities even with low differential pressures
    With tandem seat (double sealing) for low condensate flowrates
    Built-in non-return valve (only MK 45)
    Stainless steel internals (corrugated membrane of Hastelloy)
    Design “U” with undercooling capsule: utilization of a certain amount of sensible heat by banking-up of condensate, decreasing the amount of flash steam
    Optional extra: Integrated condensate monitoring for MK 45 (temperature or steam loss)

Yoshitake Steam Traps

Description

Yoshitake Steam Traps are designed for fast condensate discharge and no steam leaks. Reliable performance, high durability, easy maintenance and reduce noise. We have stocks product of Yoshitake Steam Traps with the following types.

Type

    Yoshitake Steam Traps TB-5
    Yoshitake Steam Traps TD-10NA
    Yoshitake Steam Traps TD-30NA
    Yoshitake Steam Traps TF-1 
    Yoshitake Steam Traps TF-2
    Yoshitake Steam Traps TFA-2000
    Yoshitake Steam Traps TS-1
    Yoshitake Steam Traps TS-7 
    Yoshitake Steam Traps TS-8
    Yoshitake Steam Traps TSD-7
    Yoshitake Steam Traps TSD-7F
    Yoshitake Steam Traps TSD-42
    Yoshitake Steam Traps TSD-42F

Fitur

-

Pennant Thermodinamyc Steam Trap

Description

Pennant thermodynamic steam trap are manufactured from stainless steel, this ensures mechanical and corrosion resistance. Pennant thermodynamic steam traps ensure a long operating life, ideal for fluctuating loads and pressures. We have stocks product of Pennant Thermodinamyc Steam Trap with the following type.

Type

Pennant Thermodinamyc Steam Trap PT10 -  DOWNLOAD
Pennant Thermodinamyc Steam Trap PT11 -  DOWNLOAD

Fitur

    Complete stainless steel construction ensures better mechanical and corrosion resistance properties. The disc and seat are hardened by a special induction hardening process with seat harder than disc, to withstand continuous, prolonged operation.
    Condensate entry below the disc, concentric to the disc/seat ensures a clean and parallel lift of the disc with reference to the seat, eliminating localized wear and tear.
    The inbuilt strainer screen is of adequately large area.
    Ideal for fluctuating loads and pressures.
    Perfect shut-off, no steam loss.

Pennant Ball Float Steam Traps

Description

Pennant Ball Float Steam Traps are floating type steam traps designed for the discharge of condensate from all types of steam heating and process equipment. It is equipped with excellent air ventilation and can handle heavy condensate loads. We have stocks product of Pennant Ball Float Steam Traps with the following type.

Type

    Pennant ball float steam traps comes with air vent which allows the air to pass out of the steam trap.
    Float type steam traps also comes with Steam Lock Release (SLR) unit, which can be used to avoid steam locking/flooding condition inside steam trap.
    Can handle heavy condensate loads.
    Can be customized as per customer requirements.
    Float type steam traps can offer higher heat transfer rate, discharges condensate at steam temperature.
    Pennant ball float steam traps can easily handle water hammer and sudden fluctuations in pressure and flow rate.
    Modulating discharge of hot condensate at close to saturation temperature.
    Good air venting facilitates a fast start-up.
    Modulating discharge.
    Discharges condensate at steam temperature.
    Excellent air venting (by thermostatic air vent).

Fitur

Ball Float PT61 - DOWNLOAD
Ball Float PT62 - DOWNLOAD
Ball Float PT64 - DOWNLOAD

Gestra Ball Float Steam Traps | Steam Equipment

Description

Jual Ball Float Steam Traps | Jual Ball Float Steam Traps. Steam traps with ball float for removing condensate from steam, cold condensate or distillates without banking-up. We have stock products of ball float steam traps UNA Series Gestra with the following types.

Type

    Gestra Ball Float Steam Traps UNA 14 PN 25 DN 15-25
    Gestra Ball Float Steam Traps UNA 16 PN 40 DN 15-25
    Gestra Ball Float Steam Traps UNA 43 PN 16 / CLASS 125 DN 80-150
    Gestra Ball Float Steam Traps UNA 45 PN 40 / CLASS 300 DN 15-65
    Gestra Ball Float Steam Traps UNA 46 PN 40 / CLASS 300 DN 15-65, DN 80-150
    Gestra Ball Float Steam Traps UNA 38 PN 100 DN 15-50
    Gestra Ball Float Steam Traps UNA 39 PN 160 DN 15-50
    Gestra Ball Float Steam Traps UNA Special PN 63

Fitur

    Unaffected by back pressure and condensate temperature
    No loss of live steam due to continuous water seal at the seat
    No banking-up of condensate even with extreme load and pressure fluctuations
    Particularly well suited for heat exchangers controlled from the steam side
    Unaffected by dirt
    Automatic thermostatic air-venting (Duplex design)
    Ideal for discharging cold condensates, distillates and condensates derived from chemical products (Simplex design)
    Repairable in-line
    Thanks to the rolling ball valve only reduced operating forces and small control units are required (compact, lightweight design for large flowrates)
    Internals made from corrosion-resistant stainless steels
    UNA 14, 16, 45, 46, 38: Body can be easily repositioned to convert the flow direction from left to right or vice versa or to change to vertical flow.
    UNA 45, 46 DN 40-65 optionally available with MAX controller for very large flowrates (conversion standard -> MAX controller not possible).

Gestra Drainage Module QuickEM

Description

Jual Gestra Drainage Module QuickEM | Distributor Gestra Drainage Module QuickEM. Gestra Drain Modules QuickEM are completely interconnected units for horizontal or vertical installation with or without bypass. They come with valves and steam traps, non-return valves, sightglass and shut-off valves as well as all necessary pipes, fittings, flanges, gaskets and screws. We offer Gestra drainage modules with the following types.

Type

    Gestra Steam Trap Drainage Module QuickEM
    Gestra Steam Trap Drainage Module QuickEM Control

PRODUK :
    Check Valve
    Ball Float Steam Traps
    Pressure Reducing Valve

Fitur

    Preassembled steam trap module with the recommended additional valves
    Saves time on installation
    Keeps installation errors to a minimum
    Also available without bypass
    QuickEM-Control with integrated monitoring electrode
    Standardised lengths
    For horizontal or vertical installation
    Also available in stainless steel

Gestra Vaposcope Steam Traps

Description

Jual Gestra Vaposcope Steam Traps | Distributor Gestra Vaposcope Steam Traps. Extremely clear and simple visual function test. Sightglass with borosilicate glass for checking heat exchangers and steam traps (installation upstream of traps). Visual supervision of flow conditions in condensate lines. We have stock products of vaposcope steam traps GESTRA with the following types.

Type

    Gestra Vaposcope VK 14
    Gestra Vaposcope VK 16

Fitur

    Body with straight through design and two opposing borosilicate sightglasses for improved viewing
    With mica disk as standard for higher pH values
    Valve without moving parts
    The special design of the GESTRA Vaposcope makes any loss of steam clearly visible

Gestra Thermodynamic Steam Traps DK | Steam Equipment

Description

Jual Gestra Thermodynamic Steam Traps DK | Distributor Gestra Thermodynamic Steam Traps DK. Thermostatic steam traps for removing condensate from steam or for venting steam pipes. The features of steam traps BK series highly responsive, very efficient and extremely resistant. We have stock products of thermostatic steam traps BK Series Gestra with the following types.

Type

    Gestra Thermostatic Steam Trap DK 15
    Gestra Thermostatic Steam Trap DK 27N
    Gestra Thermostatic Steam Trap DK 37/28/29 & BK 37/28/29-ASME
    Gestra Thermostatic Steam Trap DK 45/46
    Gestra Thermostatic Steam Trap DK 212 & BK 212-ASME

Fitur

    Discharge with virtually no banking-up
    Robust, insensitive regulator
    Installation in any position
    Max. admissible back pressure 80 % of the upstream pressure
    Compact, highly responsive regulator
    Small number of functional parts
    Drainage with practically no banking-up
    Any installation position – in horizontal or vertical pipes
    Reliable back pressure up to 80% of upstream pressure
    Available as an easy-to-install RHOMBUSline body with exchangeable regulator, or as a compact version
    Inner parts made of corrosion-resistant stainless steel

Gestra Thermostatic Steam Traps BK

Description

Jual Gestra Thermostatic Steam Traps BK | Distributor Gestra Thermostatic Steam Traps BK. Thermostatic steam traps for removing condensate from steam or for venting steam pipes. The features of steam traps BK series highly responsive, very efficient and extremely resistant. We have stock products of thermostatic steam traps BK Series Gestra with the following types.

Type

    Gestra Thermostatic Steam Trap BK 15
    Gestra Thermostatic Steam Trap BK 27N
    Gestra Thermostatic Steam Trap BK 37/28/29 & BK 37/28/29-ASME
    Gestra Thermostatic Steam Trap BK 45/46
    Gestra Thermostatic Steam Trap BK 212 & BK 212-ASME

Fitur

    Robust regulator for roughest operating conditions (unaffected by waterhammer and frost)
    Suitable for superheated steam applications
    Automatic air-venting (steam trap can be used for thermal
    air-venting in steam systems)
    Installation in any position (horizontal and vertical lines)
    Stage nozzle acts as non-return valve
    Extremely good start-up performance
    No loss of steam
    Suitable for differential pressure up to 275 bar
    Able to cope with the harshest operating conditions
    Any installation position – in horizontal or vertical pipes
    Inner parts made of corrosion-resistant stainless steel
    Can be serviced without removing the body from the pipe
    Metal base bushing provides the seal between the body and bimetallic regulator
    Stage nozzle for non-return valve action
    Wear-resistant